基于金属密封垫圈非线性变形仿真的预紧设计

为确保密封结构能有效阻止箱体内部介质的泄漏,要求密封面具备一定的密封比压,即通过施加合理的拧紧力矩来控制密封件的压缩量。目前主要采用试验方法验证一系列拧紧力矩下的密封效果,从而获取临界力矩值并确定可靠的拧紧力矩设计值。文章基于试验经验做出了合理的假设以建立简化的非线性有限元分析模型,对金属垫圈在压紧力下的塑性变形进行仿真,通过金属垫圈发生临界变形量的压紧力反推出拧紧力矩的临界值。该方法获取的临界力矩值与试验方法相近,可以有效地提高设计效率,降低试验成本。     

基于CAN总线的并网监控系统的设计与实现

文章以光伏并网电站为背景,介绍了一种基于CAN总线的并网监控网络系统,为了提高数据处理能力,下位机采用2407作为整机控制单元,硬件上详细论述了DSP与CAN的接口电路。软件设计则以CAN模块为主体,实现上、下位机的实时通讯,并开发了以.NET为框架的C#平台,进行了监控界面的设计。     

HB-3000型布氏硬度计换向系统的改造

介绍了ＨＢ－３０００型布氏硬度计换向系统的改造方法及改造后硬度计的工作程序，并就改进效果进行了论述。     

多机场地面等待问题模型研究

近几年世界民用航空事业的飞速发展 ,机场容量的限制引起了交通拥挤并造成了巨额损失 ,使得流量管理问题变得越来越迫切。文中针对多机场的地面等待问题 ,建立了一种行之有效的地面等待管理系统模型 ,并提出了忽略航路交叉点容量、空中延误为 0及起飞容量无限的简化模型。     

Departure Trajectory Design Based on Pareto Ant Colony Algorithm

Due to the ever-increasing air traffic flow,the influence of aircraft noise around the airport has become significant.As most airlines are trying to decrease operation cost,stringent requirements for more simple and efficient departure trajectory are on a rise.Therefore,a departure trajectory design was established for performancebased navigation technology,and a multi-objective optimization model was developed,with constraints of safety and noise influence,as well as optimization targets of efficiency and simplicity.An improved ant colony algorithm was then proposed to solve the optimization problem.Finally,an experiment was conducted using the Lanzhou terminal airspace operation data,and the results showed that the designed departure trajectory was feasible and efficient in decreasing the aircraft noise influence.     

激光功率与底面状态对选区激光熔化球化的影响

为研究激光功率与底面状态对选区激光熔化熔池流动的影响，基于离散单元法建立了选区激光熔化铺粉模型，采用粒径分布与实验相符的马氏体时效钢粉末分别铺展到平坦底面和增材底面上，将计算获得的粉末分布导入到基于有限体积法建立的选区激光熔化熔池计算流体力学模型中，研究激光功率和基板底面粗糙度对熔池流动和熔道表面形貌的影响。采用激光单道扫描实验验证铺粉模型和选区激光熔化模型。结果表明：随着激光功率的降低，单位长度的球化数量增加；由于增材底面使熔池润湿性变差，同时又对熔池流动行为产生扰动，使得增材粗糙底面上熔道的球化数量增加。选区激光熔化铺粉模拟及激光单道扫描模拟结果与实验结果吻合较好。本研究可为选区激光熔化工艺中工艺参数的选择提供理论指导。     

BP网络进行0-9十个数字图像的识别

在BP算法和数字图像处理技术的基础上,本文在MATLAB软件环境下提取Word文档中26种字体的0-9十个数字的图像,使用MATLAB神经网络工具箱及图像处理工具箱进行数字的识别,给出了较详细的处理步骤及相关程序,并比较了各种识别算法的收敛速度和识别率。     

Leakage performance of floating ring seal in cold/hot state for aero-engine

Rotating experimental investigations were carried out to study the oil sealing capability of two different floating ring seals in cold/hot state for aero-engine. High-speed Floating Ring Seal(HFRS) is a seal with the inner diameter of 83.72 mm and maximum speed of 38000 r/min, and Low-speed Floating Ring Seal(LFRS) is another seal with the inner diameter of 40.01 mm and maximum speed of 18000 r/min. In hot state, sealing air with the temperature of 371 K and oil with the temperature of 343 K was employed to model the working conditions of an aero-engine. Comparisons between floating ring seal and labyrinth seal were done to inspect the leakage performance.More attention was paid to the critical pressure ratio where the oil leakage began. Results show that the critical pressure ratio in cold state is obviously larger than that in hot state for both seals. An underlying sealing mechanism for floating ring seal is clarified by the fluid film, which closely associates with the dimensionless parameter of clearance over rotating diameter(2 c/Dr). Another fantastic phenomenon is that the leakage coefficient in hot state, not the leakage magnitude, is unexpectedly larger than that in cold state. Overall, the leakage performance of the floating ring seal is better than the labyrinth seal.     

大型齿轮在多因素耦合影响下齿形误差测量的灰色动态预报

提出了一种旁置式的大型齿轮测量装置,分析了影响该装置测量精度的主要误差来源及其特性,给出了一种处理多因素耦合影响的灰色动态预报方法.首先,基于测量装置特性,对影响齿形误差测量精度的误差源进行分析和标定,计算出各误差源的灵敏度系数;然后对测得的有限误差数据进行再抽样及灰色生成,分别计算出在每次测量中各影响因素对测量结果的作用大小,之后按照误差合成方法生成误差源耦合作用结果;最后,通过在测量结果中去除耦合作用进而提高大型齿轮齿形误差测量精度.与测量精度为0.5μm的三坐标测量机进行对比测量,结果表明所提出测量装置能满足3级精度以上的大型齿轮齿形误差检测需求.     

非静止轨道通信卫星星座间同频干扰概率分析

随着全球非静止轨道（non-geostationary orbit,NGSO）通信星座系统的大规模部署及应用,使用相同频率的星座系统之间存在着相互干扰的风险。NGSO系统间同频干扰概率的有效评估方法及合理评价指标是评估干扰风险及设计规避策略的基础,通过分析星座构型与地面站可视空域内卫星出现概率分布特性的关系,利用地面站接收端干扰噪声比保护阈值,建立了概率评估参数指标,并以OneWeb系统、O3b系统以及SpaceX系统为例,分析了全球范围地面站不同NGSO系统间发生有害干扰的概率分布特性。当系统间卫星出现概率分布趋同,会使有害干扰概率增加;反之,不同NGSO系统卫星在可视空域出现概率分布的较大差异会有效降低有害干扰概率。